(COVID-19) Status Update: PRV Audio is open and is experiencing NO DELAYS in shipping orders at this time. FREE Shipping on Orders Above $75.00

Shopping cart
$0.00
8" MID BASS NEODYMIUM LOUDSPEAKER

8MB700FT-NDY

(8 customer reviews)
In stock
  • 8″ Mid Bass – 8 Ohms
  • Neodymium Magnet
  • 98 dB – 700 Watts

$129.99

In stock

PRICE FOR SINGLE UNIT

SKU: 8MB700FT-NDY Categories: , Tag:

Features

PRV Audio’s 8MB700FT-NDY Forte Series was specially tailored to give you more power handling and less distortion. The larger voice coil ensures high heat dissipation and the necessary Bl to deliver high sensitivity even on high power with the minimum distortion.

The lower Qts allows more precise mid bass. Superior fidelity is achieved through a perfect combination of a non-pressed cone with a smooth frequency response and a surround ring specially designed to allow high displacement without increasing the distortion.

Product Highlight- 8MB700FT-NDY

Highlights

  • Nominal Impedance: 8 Ohms
  • Rated AES Power Handling (RMS): 350 Watts
  • Program Power: 700 Watts
  • Sensitivity (1W/1m): 98 dB
  • Voice Coil Diameter: 2.5″ (51 mm)

To get superior fidelity, the special composite cone is built with non-pressed paper for reduced break-up, delivering a smooth frequency response and a low moving mass, increasing the efficiency of the speaker.


8MB700FT-NDY---Close-up-shot-spider

The 8MB700FT-NDY is an extremely efficient 8″ mid bass from PRV Audio. This driver is perfect for mating to compression drivers due to its wide frequency bandwidth and its high 98 dB sensitivity rating, on 3 way system (with a suggested 95 Hz, 12 dB/octave high pass filter in place)!

Its powerful optimized neodymium motor is vented to provide excellent cooling.


Product Highlight- RK8MB700FT-NDY

 The large 2.5″ voice coil allows for the high 350-watts power handling, and warrants the outstanding cooling system implemented into the motor.

High sensitivity rating of 98 dB 1W/1M which makes it capable of generating a lot of output!


WARNING: Cancer and Reproductive Harm – www.p65warnings.ca.gov

 

Technical Details

GENERAL SPECIFICATIONS

Nominal Diameter 8″ (203 mm)
Nominal impedance 8 Ohms
Rated AES Power Handling (RMS) 350 Watts
Program Power 700 Watts
Sensitivity 2.83V at 1m 98 dB
Recommended Hi Pass Crossover**
**For Full Power Handling
95 Hz**
**12db Per Octave Crossover
Frequency Response at -10dB 70 – 5,600 Hz
Voice Coil Diameter 2.5″ (63 mm)
Voice Coil Wire CCAW
Voice Coil Winding Depth 11.3 mm
Former Material Fiber Glass
Magnetic Gap Depth 8.00 mm
Frame Material Die Cast Aluminum

 


THIELE-SMALL PARAMETERS

Equivalent Volume Vas 18.79 l
Excursion (mathematical)*** Xmax 3.65 mm
Free Air Resonance Fs 69.97 Hz
Mechanical Factor Qms 2.78
Electrical Factor Qes 0.33
Total Factor Qts 0.30
Cone Area Sd 249 cm²
Mechanical Mass Mms 23.79 g
Bl Factor Bl 12.78 Tm
Dc Resistance Re 5.2 Ohms
Inductance Le 0.34 mH at 1 kHz
Mechanical Mass Without Air Mmd 21.57 g
Mechanical Compliance Cms 0.217 mm/N

***Xmax=(Voice coil winding depth-Magnetic Gap depth)/2+ Mgnetic Gap Depth/4


EXTRA INFO

Overall Diameter 8.20” (208.5 mm)
Front Mount Baffle Cutout 7.30” (185.5 mm)
Mounting Depth 3.66” (93 mm)
Overall Depth 4.00” (101.5 mm)
Net Weight 4.32 Lbs (1.96 kg)
Shipping Weight 5.51 Lbs (2.50 kg)
Carton Dimensions W x L x H 9.05” x 9.05” x 5.11”
(230 x 230 x 130 mm)

 

Customer questions & answers

  1. 0 votes
    Q Can I run 2 of these off a 1200.4 amplifier? Would you recommend a bigger amp?
    Asked by Brent Mishler on September 5, 2020 10:25 pm
    A

    If you are only using 2 speakers I would suggest the 4 ohm version. With the 4 ohm version you can put one on each side of the amplifier, bridged. If your amp is the 4 ohm version it will work perfect. If it is the 2 ohm version it will not give enough power to see the potential of the speaker. 

  2. 0 votes
    Q How will these speakers perform in a sealed enclosure? Do they need a certain amount of airspace?
    Asked by Greg V on April 2, 2020 11:52 pm
    A

    These speakers will perform just fine in a sealed enclosure. We do not have specific requirements for airspace for this speaker. 

  3. 0 votes
    Q If I run 2 of these 8ohm 8MB700FT-NDY would wiring parallel perform better?
    Asked by Francisco on February 25, 2020 8:55 pm
    A

    You should run them in parallel and put them on an amplifier that is capable of providing 1400w @ 4 ohms. The better option would be to use the 4 ohm version if you are only using two. 

  4. 0 votes
    Q What ohm amp do I need to run 4 of them.. 2 in each bag.? all in parallel
    Asked by Jermane L Gartrell on February 5, 2020 4:42 pm
    A

    If you run 4 of these together you will need a 2 ohm amplifier. 

  5. 0 votes
    Q If I wanted to run 6 of these, what amp will push all 6 speakers?
    Asked by Haynes on January 8, 2020 12:29 am
    A

    You can use the PRV A1MH PRO 1 Ohm. Follow this link: https://prvaudio.com/products/a1mh-pro/

Send me a notification for each new answer.

8 reviews for 8MB700FT-NDY

  1. Jay

  2. Duncan S.

    All I can say is buy them and you won’t be sorry. Very good speakers.

  3. Jimmie Poole

  4. Victor T.

    Excellent speaker for an HD set up.

  5. Cesar

    Excellent

  6. KEITH FOSTER

  7. Yssan

  8. Dameion

    These sound awesome

Add a review

Your email address will not be published. Required fields are marked *

Repair Parts

Recone Kit for 8MB700FT-NDY Loudspeaker

 

Videos